抗倍特掛墻板就是以抗倍特板為原材制成的掛墻板，抗倍特板的材質采用的是“HPL”的制作技術，表層是裝飾紙，提供表面花色起到裝飾作用，基層是浸酚醛樹脂后牛皮紙排疊壓合而成，密度達到1.5左右，強度大、抗撞擊、結構穩定、易清潔，十分適合做掛墻的各項使用條件，所以在市場的使用量非常大。下面來講講富美家抗倍特掛墻板的基本安裝步驟。

Kangbeite wallboard is a kind of wallboard made of Kangbeite as raw material. The material of Kangbeite wallboard is made of "HPL" technology. The surface layer is decorative paper, which provides decorative effects. The base layer is made of laminated kraft paper impregnated with phenolic resin, with a density of about 1.5. It has high strength, impact resistance, stable structure, and is easy to clean. It is very suitable for various use conditions of hanging walls, Therefore, it is widely used in the market. Now let's talk about the basic installation steps of Fumeijia Kangbeite wall panels.

（1）測量墻面。這是一個安裝抗倍特板板墻的步驟。只有通過測量墻面，才能計算出需要多少單片或單片墻板。首先測量墻面的長度和寬度，根據墻板的尺寸計算出墻板所需的整數塊。多余的空間可以通過拼接墻板來完成，拼接應分布在末端。

(1) Measure the wall. This is a step to install the anti multiplier special plate wall. Only by measuring the wall surface can we calculate how many single pieces or single pieces of wallboard are needed. First, measure the length and width of the wall, and calculate the integral block required by the wallboard according to its size. Excess space can be completed by splicing wallboards, which should be distributed at the end.

（2）安裝踢腳線。踢腳線可以進行很好的保護環境墻面，所以我們這是抗倍特掛墻板安裝應用程序中非常重要基本的一步。一般的來說，要先在墻面上鉆孔，用膨脹螺絲或鋼釘將踢腳線掛鉤固定在墻上。然后在鉤子上掛上一條一端為45°角的踢腳線。

(2) Install the skirting. The skirting line can protect the environment and wall surface very well, so this is a very important and basic step in the installation of Kangbeite wallboard application. Generally speaking, drill holes on the wall first, and fix the skirting hook on the wall with expansion screws or steel nails. Then hang a skirting line with an angle of 45 ° at one end on the hook.

（3）安裝掛墻板。 做好以上述兩個重要步驟以后需要我們生活就要不斷進行掛墻板安裝了。首先，將抗倍特掛墻板從左向右慢慢插入做工精良的護壁線，然后在護壁線以上約1.5厘米的位置（板寬在中間）安裝膨脹螺釘或鋼釘。需要提醒的是，安裝墻板時釘子不能露出。

(3) Install wall panels. After completing the above two important steps, we need to continuously install wall panels in our daily life. First, slowly insert the Kangbeite wallboard from left to right into the well made wall protection line, and then install expansion screws or steel nails about 1.5 cm above the wall protection line (plate width in the middle). It should be noted that the nails shall not be exposed when installing the wallboard.

（4）安裝頂角線。頂角線又稱陰影角線，是指墻壁與天花板之間的那條線連接。通常處理這種頂角線的方法是在兩邊涂上特殊的膠水，然后貼在頂角，拉開幾分鐘，然后貼緊。

(4) Install the top corner line. The top corner line, also known as the shadow corner line, refers to the line between the wall and the ceiling. Usually, the method to deal with this kind of top corner line is to apply special glue on both sides, then stick it on the top corner, pull it away for a few minutes, and then stick it tightly.

此外抗倍特板雖然成品無法做彎曲，但是是可以定制彎角，所以在安裝過程中彎角不好處理的話可以跟商家提要求的；還有就是每張板之間還是需要預留3-5mm的縫隙，不要全部靠在一起，為熱脹冷縮留出空間，不然容易擠壓變形；那些縫隙如果覺得不美觀，也有一些配合安裝的金屬條可以用。更多相關內容了解就來我們網站http://m.www77mmnncom.cn咨詢吧！

In addition, although the finished product cannot be bent, the bending angle can be customized, so you can ask the manufacturer if the bending angle is not easy to handle during installation; In addition, 3-5mm gap should be reserved between each plate, not all of them should lean together, and space should be reserved for thermal expansion and cold contraction, otherwise it is easy to extrude; If those gaps are not beautiful, there are also some metal strips that can be used for installation. For more information, please come to our website http://m.www77mmnncom.cn Consult!